铝卷消费厂家引见铝卷的加工及上色步调_讯息资讯

www.bifa365.com-365必发登陆_平台网站

铝板消费厂家

您的地位:首页 > 讯息资讯 >

铝卷消费厂家引见铝卷的加工及上色步调

来路:  公布日期:2020-11-24 15:05:19  

铝卷厂家引见铝卷上色进程:
Aluminum coil manufacturers introduce the process of aluminum coil coloring
1、预处置,先运用办法对表面停止洗濯,运用物理和化学办法都可以,最次要的便是使铝卷.如许是有利于氧化的完好的停止的,组成的氧化膜也会是精密的.预处置还可以运用一些机器设置装备摆设处置.
1. Pretreatment, the use of methods to clean the external surface, the use of physical and chemical methods can, the most important is to make aluminum coil. This is conducive to the complete oxidation, the composition of the oxide film will be fine. Pretreatment can also use some mechanical equipment
2.阳极氧化,铝卷厂家经过与处置之后的铝卷,使基体发作阳极氧化反响,然后便是会天生精密的氧化薄膜.
2. Anodizing: aluminum coil manufacturers will react with the aluminum coil after treatment to form a fine oxide film


3.封孔,经过阳极氧化之后,氧化薄膜上会出现很多的膜孔,封孔便是使这些膜孔封闭,避免氧化膜被净化.这种氧化膜是透明的,而且是具有吸附性的,如许就会在孔内聚集一些金属盐,如许就能在表面显表现一些副本的雪白色,或许是之外的很多颜色.
3. Sealing, after anodizing, there will be many film holes on the oxide film. Sealing the hole is to close these film holes and prevent the oxide film from being polluted. This kind of oxide film is transparent and has adsorption, so some metal salts will be accumulated in the hole, so that some original silver white or many other colors can be displayed on the surface
铝卷消费厂家
Aluminum coil manufacturer
铝卷假定要投入运用,要在正常的温度下,温度不克不及过热也不克不及太酷寒,假定作为屋面,高度不得低于10度。在安装之前,实时停止反省,包管屋面的材料没有磨损的表象,包管可以正常的运用,在正常的状况下包管运用的寿命。铝卷厂家螺栓头要用防水性强的物质密封,避免雨水进入生锈。
The aluminum coil is supposed to be put into use. The temperature should not be too hot or too cold under the normal temperature. It is assumed that as the roof, the height should not be less than 10 degrees. Before installation, timely inspection shall be carried out to ensure that there is no appearance of wear and tear on the roof data, so as to ensure normal operation and service life under normal conditions. The bolt head of aluminum coil manufacturer shall be sealed with waterproof material to prevent rainwater from entering and rusting.

铝卷加工的情况温度应在7℃以上,要依据铝卷厚度调解加工辊系的清闲,并根除辊面及托板上的异物;一同要反省铝卷双面是不是脱漆,如脱漆,应查明缘由且采用方法后本领持续加工。
The ambient temperature of aluminum coil processing should be above 7 ℃. The gap of processing roller system should be adjusted according to the thickness of aluminum coil, and the foreign matters on the roller surface and support plate should be removed. It is necessary to check whether the paint on both sides of the aluminum coil is peeling off. If the paint is removed, the reason should be found out and the method should be adopted before continuing the processing.

xml地图

Baidu
sogou